Manual 06 - Volume Rocker

Before disassembly, thoroughly wash and dry your hands.

Power down the device.

Remove the SIM card and SD card: push card in and it will pop out. Place both in COMPARTMENT A.

Picture 1: Use the guitar pick to gently pry between the battery cover and front panel.

Run the pick around the entire perimeter of the phone to release clips securing the battery cover.

Picture 2: Adhesive holds the battery cover in place. Continue peeling the battery cover up with your fingers until it reaches the amount of separation seen in the picture. You'll begin to feel tension from the adhesive when you reach to correct amount of separation.

Work your way around the entire perimeter of the phone.

Picture 3: Run the guitar pick between the battery cover and rear camera trim to release final clips (red square).

Picture 1: Apply low-level heat (100° Celcius) all over the back of the phone for 60 seconds to loosen the adhesive securing the battery cover. Apply heat to the Motorola symbol in the middle for an additional 15 seconds.

Picture 2: Use your fingers to gently peel the battery cover from the phone.

Take care when peeling up the Motorola symbol - it has a tendency to stay stuck to the battery.

Picture 3: Finish removing the battery cover, noting the battery cover is fairly flexible.

Place battery cover in ZONE I.

Picture 1: Apply low-level heat (100° Celcius) to the Camera Trim for 30 seconds.

Picture 2: Wedge the iSesamo under the upper-left corner of the rear camera trim.

Picture 3: Replace the iSesamo with a guitar pick.

Picture 1: Use a guitar pick to peel up the right side. If you encounter resistance, apply more heat.

Picture 2: Once the rear camera trim is completely free, place in COMPARTMENT C.

Remove three 6.7 mm silver T3 Torx screws and place into SLOT 1.

Remove four 4.0 mm gold T3 Torx screws and place into SLOT 2.

Remove three 4.5 mm black T5 Torx screws and place into SLOT 3.

With the phone face down wedge the guitar pick between the display and mid-frame in the upper-right corner. Run the guitar pick down the right side to release clips holding mid-frame to the display.

Use your fingers to continue peeling the remaining clips holding the mid-frame to the display.

Place the mid-frame into ZONE II.

Picture 1: Remove the rubber screw cover and place into SLOT 4.

Picture 2: Remove two 3.3 mm T5 Torx screws and place into SLOT 5.

Picture 1: Apply low-level heat (100° Celsius) to the screen to loosen adhesive holding the battery in place.

Pictures 2 & 3: Wedge spudger underneath the notch in the battery in the lower-right corner and pry up.

Pry up around the edges to free the adhesive holding down the battery.

Remove the battery starting in the lower-right corner.

Use the battery removal tab to finish removing the battery once it's nearly free. Place it in ZONE III.

Remove three 2.5 mm T3 Torx screws and place in SLOT 6.

Lift the metal chassis from the logic board. Place in ZONE IV.

Gently peel the volume rocker clockwise to free it from the front panel.

Place volume rocker in COMPARTMENT B.

Picture 1: Retrieve volume rocker from COMPARTMENT B:

Picture 2: Note the orientation of the volume rocker: line up the tabs on the volume rocker with the corresponding slots on the front panel.

Picture 3: Push volume rocker into place.

Seat the metal chassis on the logic board from ZONE IV.

Replace three 2.5 mm T3 Torx screws and from SLOT 6.

Picture 1: Retrieve battery from ZONE III. Place the battery into the metal chassis frame.

Picture 2: Replace two 3.3 mm T5 Torx screws from SLOT 5.

Picture 3: Replace the rubber screw cover from SLOT 4.

Seat the mid-frame from ZONE II on the display assembly.

CHECK PLACEMENT OF MIC COVERS.

Secure the clips: Snap the top of the mid-frame into place and work your way down.

Picture 1: Replace three 4.5 mm black T5 Torx screws from SLOT 3.

Picture 2: Replace four 4.0 mm gold T3 Torx screws from SLOT 2.

Picture 3: Replace three 6.7 mm silver T3 Torx screws from SLOT 1.

Retrieve the rear camera trim from COMPARTMENT C. Starting from the left side, reapply the rear camera trim and press firmly to resecure it to the phone.

If the trim is loose, try heating the area to reactivate the adhesive. Apply pressure until the trim is secure. (If necessary, apply thin strips of double-sided adhesive to secure the trim.)

Picture 1: Replace battery cover from ZONE I.

Pictures 2 & 3: Press firmly along the top edge to secure the battery cover.

Pictures 1 & 2: Press firmly along all edges of the phone to secure the clips.

Picture 3: Run your fingers along all edges to ensure all clips are secured.

Replace SIM card and SD card from COMPARTMENT A.

Power up device and test replaced component or components.